Hydraulic pumps in energy and power applications
7 images · hover the main image to magnify, click for full size; point at a thumbnail to preview
Lubrication, shaft lifting, sealing oil and governing all rely on auxiliary oil systems around the main machine. The article sorts the pump sets by function and explains redundancy.
In a power station the main machine is a steam turbine, a water turbine or a wind rotor, but what keeps that machine safe is the auxiliary oil system spread around it. What a utility buys is usually not a single pump but a motor-driven pump set: motor, coupling, pump, safety valve, filter, valves, oil tank or skid base frame and local control supplied together, which makes installation, testing and spare parts management simpler.

Which pump sets a power plant contains
By function there are four groups. Lubricating oil pump sets feed the bearings and gears continuously. Jacking (high-pressure) oil pump sets lift the main shaft on a starting machine so that an oil film forms before it turns. Sealing oil and fuel oil pump sets serve the hydrogen-cooled generator seal and the boiler light-off and fuel supply respectively. Governing and hydraulic control pump sets supply pressure oil to the guide vanes, gates and valves of a water turbine. The pressure levels of these circuits differ widely, from low-pressure high-flow circulation to control oil at several tens of bar, so each needs its own selection instead of one set of numbers for all.
Thermal power: lubrication, shaft lifting, sealing and fuel
Bearing lubrication of a gas turbine or steam turbine needs a continuous flow at steady pressure. The jacking oil pump carries the high-pressure lifting duty during start-up. The generator sealing oil pump must keep its oil pressure above the hydrogen pressure inside the machine. Fuel transfer and light-off pumps move the fuel from storage tanks to the burners. The three-screw pump is widely used in these circuits because its flow has no pulsation, it self-primes well and it runs quietly. Coal mill lubrication stations are normally arranged as one duty and one standby: when the running pump trips, the standby starts automatically so that the auxiliary machine never loses its oil supply.
Hydropower and pumped storage: the governor pressure unit
A water turbine governing system answers load changes frequently, so its pressure unit lives in a repeated cycle of building pressure, holding it and releasing it, which puts fatigue demands on the pump body, the bearings and the rotating parts. Governor pressure units, turbine bearing lubrication and jacking oil systems commonly use a medium or high-pressure three-screw pump or a high-pressure screw pump. Published records of large hydropower auxiliary systems show these arrangements in volume; they are useful for understanding the pressure level and the redundancy thinking behind them, but the figures for a specific station must come from the technical documents of that station.
Wind and nuclear: gearbox lubrication and high reliability
The gearbox oil pump of a wind turbine sends gear oil out, through filtration and cooling, and back to each lubrication point; cold starting and the high viscosity that goes with it are the hard part of the selection. A nuclear plant asks stricter control of the overall performance of a pump set, of its seals and of material traceability. Where the oil carries a relatively high amount of entrained gas, a screw pump still runs quietly, which is a real advantage over a gear design in that condition.
Set integration and redundancy
Motor-pump set design should state each item one by one: the medium and its viscosity range, the flow and the inlet and outlet pressures, motor rating and protection class, safety valve setting, filter rating, base frame form, connection standard, and whether explosion-proof equipment is required. For lubrication and shaft lifting, and for other essential circuits, one duty and one standby unit is recommended, with pressure, temperature and differential-pressure monitoring and automatic change-over and alarm. HAIGTS supplies motor-and-screw-pump and motor-and-high-pressure-pump industrial electro-hydraulic solutions, SMT, SMT16B, SNH, SMH and GR series three-screw pumps, custom power units and matching coolers, and can deliver them integrated on a skid. On a retrofit where space is tight, check the original flanges and pipe connections first so that field modification stays small.
Summary
Related products: industrial electro-hydraulic solutions (motor and pump sets) SMT series three-screw pump SMT16B series three-screw pump GR series high-pressure screw pump custom power unit COL-d plate-fin cooler
The reliability of power plant auxiliary systems comes from splitting the pressure levels correctly, from redundancy, and from testing the pump set as a complete supply. Tell us the medium, the flow and pressure, the oil temperature range, the control method and the connection standard, and we can issue the pump set schedule. Telephone: +86 22 22974590.

Note: the division into thermal, hydro and wind circuits follows published industry material. The large engineering projects mentioned are given only as technical background and are not delivery records of this company.
Parameters
- 树脂
- 干燥