Wind power
Hover to magnify, click for full size
Wind turbine lubrication and hydraulic systems live inside the nacelle: the gearbox runs splash plus pressure feed with staged oil temperature control, while pitch and brake circuits hold pressure from a gear pump power pack with accumulators. This page gathers the published figures that matter for pump and cooler selection.
Almost all the lubrication and hydraulic equipment of a wind turbine sits inside the nacelle. Space is tight, service windows follow the wind and the crane plan, and the oil system has to work through cold high-viscosity starts, load swings and long unmanned periods. How well gearbox supply, pitch and brake pressure, filtration and cooling hold together decides availability, and how often somebody has to climb up.

Gearbox lubrication: splash plus pressure feed
Gearbox oil has to lubricate, cool, clean and protect at the same time, so medium and large units combine splash lubrication with a pumped, forced circuit: the pump sends oil through the filter and the thermal control valve to the distributor, and from there onto the tooth flanks, the bearings and the high speed shaft. Published descriptions usually describe a staged duty: the low speed pump runs at start, the high speed pump joins in above roughly 40 C; below roughly 45 C the thermal valve routes oil straight into the gearbox, above it the oil passes the cooler; near 55 C of oil or above 70 C on a high speed shaft bearing the cooler runs at full load and steps back once the temperature falls. Pressure sensors sit at the gearbox inlet and at the pump outlet, a safety valve limits over-pressure, and the circuit needs a way to release air, because bubbles in the oil show up on the teeth and bearings before anything else.
Pitch and yaw: a gear pump power pack holds the pressure
The hydraulic system of a variable pitch machine normally has two pressure holding circuits: one feeds the pitch cylinders through an accumulator and a proportional valve, the other feeds the high speed shaft brake and the yaw brake from an accumulator. Published data for one machine family list a gear pump as the power source, shared by the pitch circuit and the brake circuit, with a pressure switch starting and stopping the pump in a band of about 130 to 145 bar, a relief valve set at 145 bar, a high pressure filter with bypass valve and contamination indicator, a check valve against back flow, an adjustable throttle valve used to release accumulator pressure before service work, an oil level switch that protects against overflow and dry running, and a PT100 element in the tank. Yaw brakes typically release by compressing springs with high pressure oil and close again when pressure drops; after a set number of cable twists the nacelle turns the other way and the brakes open fully. A separate automatic system, a grease pump with a distributor, feeds the yaw bearing and the ring gear continuously instead of interval greasing by hand. Electric pitch and mixed electro-hydraulic pitch also exist, and direct drive machines have no gearbox at all, so the duty of the pump differs from one design to another: geared machines are about lubrication and heat, hydraulic pitch machines are about holding pressure and keeping the oil clean.
Cold starts and oil condition
The complaint most often reported in winter is pump motor overload. After a long standstill the heater of the gearbox cannot bring the oil up to working viscosity, so the motor is overloaded at start. Maintenance literature recommends keeping the machine in standby and warming the gear oil up step by step before starting, rather than forcing a start, because poor lubrication at that moment damages the tooth flanks and the bearings. A second cause with older machines is an aged shaft seal on the pump motor, letting gear oil reach the terminal box and causing poor contact and unbalanced three-phase current. Oil monitoring follows guidance such as DL/T 1461-2023 for gearbox oil in service: viscosity is allowed to move by roughly 10 percent against new oil, a rising acid number marks oxidation, water promotes emulsion and additive hydrolysis and is linked to hydrogen induced fatigue, cleanliness is reported as ISO 4406 codes at 4, 6 and 14 micrometre, and spectral analysis watches wear elements such as iron and copper against contaminants such as silicon and sodium. Samples should be taken hot, from the sampling valve, after the dead oil in the line has been flushed out. Synthetic gear oils of the PAO and PAG family keep better low temperature flow, which is why they are common in cold climates.
Heat exchange and cooler choice
Air coolers are the most common choice inside the nacelle: a fan blows across the finned core, and the fins need regular dust cleaning. Water cooled plate or shell and tube units give more capacity where cooling water is available, and are found more often at the tower base or in a ground oil station. Published retrofit practice for a hot gearbox comes down to two routes, a larger exchanger core or more airflow from the fan, and both have to be done without changing the flow and pressure at each lubrication point. Offshore units add salt spray, ingress protection and the crane window to the same list.
What to send for sizing
To match a pump and a cooler, give the full set in one message: oil grade and viscosity at 40 C, total gearbox volume and the flow split per lubrication point, supply pressure and allowable differential, target oil temperature and the changeover point of the thermal valve, mounting form (horizontal, vertical, submerged, or built as a motor pump set), the working temperature range with the lowest ambient value, the relief valve setting and the available power supply.
Summary
Related products: SNH low pressure triple screw pump SMH medium pressure triple screw pump SMT16B series triple screw pump HPG3 high pressure gear pump HF3 air cooler FF10 large air cooler COL-d plate fin cooler motor pump set
Selecting pumps and coolers for wind power means matching cold start viscosity, the staged oil temperature duty and the pressure holding needs of pitch and brake circuits to a specific model. A related comparison across thermal, hydro and wind duty is in lubrication and cooling in the electric power industry. Telephone: +86 22 22974590.
Note: the figures above are technical ranges taken from published industry material, given for sizing discussion only. They do not represent measured data or a specific delivery record of HAIGTS.